Major Project: Hexacopter Drone

(The fifth in our student blog series, written by Sam in 11th Grade, is followed by the teacher's two updates on the project, so please read all the way down! Flight tests were finally successful, as students and teacher alike learned the hard realities of "going back to the drawing board!")

While we don’t plan on taking him to the sun, Icarus was the name we selected for our massive hexacopter drone. With a 31-inch diameter, and the theoretical ability to lift almost two pounds on top of its own five-pound weight, it is operating at the higher end of recreational drone constraints. Most commercially available drones today feature only four propellers, and a mass of around one pound.

Early sketches of the design, with design priorities listed on the side

When we were designing “Thiccarus” we decided to push the boundaries with the materials we had available. A hexacopter design, as opposed to a more common quadcopter (a standard recreational design with four propellers), gave us more lift power and stability with a trade off on speed and maneuverability. To reduce weight and maintain strength Thiccarus would be constructed with 3D printed body parts and carbon fiber struts connecting them. However, when we were brainstorming, we decided that our drone’s primary function would be cargo delivery (despite my suggestions to make it into a fishing drone or a laser-toting drone with a search and destroy mission).

Pedro, Nolan, and Joshua tear apart
old quadcopter drones from two years
ago--fare thee well!

We came up with our design, then our constraints and requirements. After this, we split into design teams, each headed by ”captains.” After the protective shrouds around each propeller and control center base were decided upon, we set to starting a joint Onshape project. Onshape is our 3D design platform of choice for this project. Each team member was assigned one component of Thiccarus to design, and it came together well in a collaborative fashion. Each member of the design team is able to see in real time how their part will integrate with the other parts, which is incredibly helpful.

The eight students work concurrently on the drone CAD model,
with each one instantly able to see how their component fits into
the broader scope

The hexacopter design emerges!

The largest and most difficult piece to print: the central electronics
platform; five or six attempts at printing were required

Icarus is currently in the printing stage, and when it is fully constructed, it will be mounted with two cameras feeding to a battery powered LCD screen. Steered by the controller, it will be capable of flying high and low to deliver small payloads.

(Sam's article was written in early October. After a delay in printing production due to some technical difficulties, the entire drone was finally fully assembled and taken for some early test flights. And now the update—which gets a little technical...)

After many hours of printing and assembly...

Sam, Ben, and Todd carefully attach
the motors and batteries and other
electronic components

The 8th Period engineering class proudly marched their huge drone out to the Providence soccer pitch. Gentle (and safe!) power-ups in the classroom had proved troublesome, with erratic behavior being immediately apparent. The drone was very touchy, and tended to spin around and roll to one side. Cutting the throttle from even six inches of altitude caused the aircraft to fall with a ungraceful "thump", with small 3D-printed pieces occasionally breaking off.

Alena gave an insightful suggestion that we could take it outside and stretch out a big sheet of fabric to catch the drone as it fell. This would allow us to try to gain more altitude—and more time to evaluate its behavior and get it under manual control. The soft fall into the fabric would certainly keep both drone and students completely safe! As an added bonus, we would look comically like cartoon fire-fighters.

The group heads outside to try an initial flight: safety goggles on!

And look like cartoon fire-fighters we did! The plan worked rather well, except for Ben slipping accidentally in a mud patch on the field in his zeal for saving the drone. With the extra flight altitude and time, we learned that the machine wanted to spin on its vertical axis—absolutely out of control. Where it should have lifted gingerly into the air and hovered obediently, it was a veritable whirling dervish, and the group could not even agree on their recollection of whether it had spun clockwise or counter-clockwise!

It may look like the class is flinging it into the air—we promise
it is actually flying!

In a typical situation like this, the pilot should be able to add in some "yaw" trim. This means that the controller is set to always provide a little bit extra of yaw control, intended to counteract whatever is naturally happening and make everything balance out again. But adding yaw trim in either direction just didn't change anything, and after one particularly wild spin the drone fell outside of the fabric and broke one of its 3D-printed propeller shrouds.

See that tilt to one side? About three seconds later Thiccarus
successfully escaped our circle of friendship!

Back to the drawing board...

1. It is possible that the flight controller—the 1-inch small box that houses gyroscopes and inputs and outputs and magnetometers and so on—is just misbehaving or badly calibrated. But after several recalibrations and trying an alternate one that we had in stock, there was no improvement. Check.
2. Is Thiccarus just way too "thicc"? Maybe. We could have designed more aggressively, and perhaps brought him down to 2 kg even (4.4 lb). But the specs say that each motor should be able to create up to 550 grams of thrust. With six motors in total, that's 3.3 kg of thrust available (7.3 lb). And it's definitely getting off the ground, even with the thrust output turned down for safety. So: check.
3. It is possible that one or more motors are just misbehaving or getting bad signals. Tiny, threadlike wires carry the commands between the different components, and we have run into problems of this nature before. But replacing one bad cable fixed that, and simple individual motor bench tests show snappy, responsive motors that will blow your papers away from across the room.

When all else fails, Google it. Apparently, when your drone experiences untrimmable yaw, it is likely the result of not having set all motors perfectly level. In other words, one or more propellers might not be perfectly flat relative to the ground, but tilted slightly to one side. And yes, this is quite noticeable on poor old Thiccarus once you look for it. Fortunately, it can be easily solved by readjusting the four screws that hold each motor down, and putting a little "shim" on one side to nudge it up to level.

This is actually an interesting application of standard high school trigonometry. If a thrust vector is pointing straight up to sky, well and good. This is what the flight controller is banking on for its power distribution calculations. But if a motor is tipped to one side by even two or three degrees (barely perceptible to the eye), the aircraft will experience a mysterious lateral force equal to the thrust times the sine of the angle. If the motor is generating a healthy 500 grams of thrust (a little over a pound), three degrees of tilt creates 26 grams of sideways thrust (500sin3°). Small but significant—and the flight controller is not accounting for it.

Maddening: yes. Fixable: absolutely. The motors will be checked and adjusted, and Thiccarus will be bandaged up and flown again. It is also very likely that a Mark II design will surface in the second semester, with higher tolerances for motor angles accounted for from the very beginning and a lighter airframe. Less airframe weight means longer flight times, a more responsive drone, and a greater possible payload.

Providence Engineering Academy: carry on!

(Our final update for this story on the 19th of November.  Spoiler alert: it's a happy ending!)

As promised, the motors were checked and adjusted. Ben and Mr. Meadth stayed after school and carefully placed pieces of card under this or that side of the motors to shim them up, bringing them as close as possible to vertical. Three motors were in need of adjustment, but none of them were out of line by more than about two or three degrees.

The drone was powered up, with high hopes... but the end result was exactly the same. Thiccarus wanted to flip over to the side and rotate faster and faster, and nothing could persuade him otherwise. Forget flying too close to the sun—Thiccarus couldn't even get off the ground!

And then...

And then...

Mr. Meadth had his flash of inspiration, and it all came down to this image:

The source of all problems.

This diagram shows the initial wiring and setup instructions from the flight controller. A certain teacher thought he had carefully followed the diagram; unfortunately, he had set the actual propeller directions all opposite. For example, propeller 1 was supposed to be rotating clockwise, but it had been set up to be counter-clockwise.

What's the big deal, you ask? Well, while having everything opposite would still be balanced to some degree, the flight controller uses the spinning propellers to control its yaw. Say the craft wants to yaw to the left, it chooses a propeller to spin faster to the right (like propeller 1), and Newton's Law of Reactions takes over. If it wants to yaw to the right, it might choose a left-spinning propeller to do that (like propeller 2). But since each and every one was backwards, the corrective actions it tried to take were in every case making the situation worse. If it started drifting left, it would end up spinning more left—a classic vicious circle if ever there was one.

A quick click of a checkbox in the computer and that was solved. All propellers: backwards. Oops.

Propellers... spinning the correct way!

You know you're doing something
right when you're looking at the bottom
of the drone

This portable outdoor screen receives
video input from two onboard cameras

Today marks another successful series of flights. We currently get about ten minutes of air time with two fully charged batteries. Three students plus teacher have been brave enough to fly around a little bit. No major accidents—perhaps a leg snapping off here or there with a rough landing!

Lessons learned:

1. Persistence pays off. If this is a thing that can be done, then you can do it. Just get out there and keep troubleshooting until you work it out.
2. This is a new era of high school education. To collaborate on a CAD model, 3D print it, order the electronics, and create a hovering 2.2 kg monstrosity in the space of three months is just not something a school could have done in-house ten years ago. Truly these are amazing times!
3. These students are capable. With the right leadership and direction, they know how to think and problem solve and calculate and design. They will go far.

The story ends here, but keep an eye out for Mark II! We just can't resist. There are already so many things that could be optimized (chiefly, stronger airframe and lighter weight). Lighter weight means more air time, so bring it on! Look out for Son of Thiccarus in the second semester, and until then, stay posted.

Collaboration with the Physical Education Department

(The fourth in our student blog series comes from Nolan in 11th Grade, and gives the final update on a project that was begun last year.)

Last year, the focus of the Advanced Engineering I group (juniors and seniors) of the Providence Engineering Academy was statics, or the branch of physics associated with objects at rest. As a way to explore this topic, the members of the Engineering Academy collaborated with the Providence Physical Education Department. Their goal was to create versatile wooden boxes that could function in many different ways: an obstacle course, a balance beam, or a step-up box, for example. In this way, the engineering students created a system that would not only benefit the P.E. program, but would also help them learn more about statics, since the structure would have to be able to withstand the use of the junior highers (not breaking or sliding on the grass when jumped on, while having multiple uses).

The first box shown in a virtual assembly

The second box shown translucent, interior strength wall visible

This first step of this project was to create paper models of the boxes, to see how everything would fit together. After Mr. Meadth, the director of the Engineering Academy, approved the designs, the team shifted to using an online program called Onshape. Onshape is a design tool used to create realistic models of objects. This CAD technique allowed the budding engineers to visualize their designs of the boxes further and make adjustments where needed. Once the “CADing” was complete, it was time to start producing and assembling the actual boxes.

Mr. Meadth checks the fit of the first two pieces of one box, as
students look on

The students wrestle with the heavy pieces, sliding them into place

Incorporating the “box joint” technique (resembling a three-dimensional puzzle, used for strength), the two large boxes were finally completed after lots of hard work from last year’s juniors and seniors. Each box comprised approximately nine pieces, weighed about 120 pounds, and had volumes of 80 and 48 cubic feet, respectively. Another fun touch added to these boxes was a grid of four inch squares cut into sides of the boxes, allowing them to be connected together with beams. These boxes are oddly shaped, one like a cube cut along the diagonal and the other like a cube with a rectangular chunk missing, which only adds to their versatility.

An almost completed box, missing two faces and the inner wall

Fast-forward three months: two
amazing boxes just as planned!

Since these boxes were created last year, they have had much use from the junior highers. Mr. Mitchell, the P.E. teacher, says that he is “very grateful that the Engineering Academy did this," and that "these boxes really enhance the fitness pursuits and the program as a whole." Judging by the frequency of use and Mr. Mitchell's gratefulness, this project was a resounding success. Great work, Providence Engineering Academy!

A grateful Mr. Mitchell urges his students on as they create
innovative workout routines

Inspiration from Michele Weslander-Quaid

(The next in our student blog series comes from Madison in 12th Grade.)

Earlier this semester, our Providence Engineering Academy had the honor of hearing from Michele Weslander-Quaid. She shared a brief description of her life growing up with many challenges and gave us the charge that we are never too young to lead or change the world. 

Despite some disadvantages in her background, Michele was able to accomplish incredible things, which she attributes largely to her mother’s sacrificial parenting sending her to a Santa Barbara Christian School. She went on to be the youngest Chief Engineer and the second female Chief Engineer in the history of her company, one of the youngest Senior Executives in U.S. Government history, and Google CTO for Public Sector and Innovation Evangelist.

Michele shares the wisdom she has learned over the years

Michele went on to tell us that too often people are judged by the circumstances into which they were born. She encouraged us that even if we have rough backgrounds, we should not let our disadvantages hold us back from our dreams for the future or let past experiences decide our fate. 

One of the powerful quotes she mentioned was by Charles R. Swindoll saying: “Life is 10% what happens to you and 90% how you react to it.” Life is all about the decisions we make based on events that have happened to us, not the events themselves. We can choose to let our past experiences or upbringing lead us to a never-ending cycle for generations to come, or we can stand up against those tendencies and do great things. We are in control of our own destiny.

The entire Academy poses with our guest!

A couple of years ago Michele spoke to us and gave a similar charge that we are never too young to change the world. It was that presentation that encouraged me to pursue a particular future for myself: to enter into one of the military academies as an engineer. 

I am still actively working today to reach that goal because of her. Michele is such an inspirational speaker and I hope that other students—or even adults—will realize that the difficulties of their past need not define their future.

Thank you again, Michele, for inspiring us with your life story.